Die spotting & try out press   Manufacturer H Type 1008-Z Touching force 100 kN Year of construction 1995 Note   Technical data   Pressing and clamping pressure 100 - 1000 KN Operating pressure max 250 bar Drive line pump 4 kW Pressing speed 6 mm/s Pressing speed up 30 mm/s Pressing speed down 15.5 / 6 mm/s Ölfülling 190 l Stroke Stö&Aerospace;el 250 mm Pulling pressure 400 KN Pulling stroke 125 mm Number of drawing pins 8 pcs Ø Draw studs 24 mm delivery time immediately Price on request

Spotting try out press   Manufacturer Schuler Model SHC-2500-5.0x2.5 spotting force 2500 to Year of manufacture 2014 Comment   Facility data   Place requirement   Foundation depth (table flureben) 5,000 mm Press weight with tooling and Ölfülling ~540 to Foundation load   Static load 274 N/cm² Static & Dynamic load 345 N/cm²  Energy demand   ElectricalPower consumption (without taking into account power factor correction) ~1,100 kVA Apparent power ~830 kVA Reactive power ~360kVA  Average energy consumption(under production conditions, i.e. In continuous press operation) 400V 3/PE 50Hz  Operating voltage 24VDC Control voltage 230V AC 50Hz  Voltage for lighting 230V AC 50Hz  Allowable voltage fluctuations +/-10  % Compressed air   Low pressure network, minimum pressure 5 bar     Ölquantity  ~11,000 l Kühl water   Kühl water requirement(under production conditions, i.e. in the continuous run of the press) approx.14 m3/h Water inlet temperature max. 25 °C Water outlet temperature approx.35  °C Pressure difference ca. 2.5  bar Technical data press   Type SHC-2500-5.0x2.5 Number 1 Pressing rod   Pullingö&stroke;el force 3,750 - 25,000 kN Gross pullback force approx. 1,750 kN Draw ram stroke 1.700 mm Drawing height (width x depth) 5,000 X 2,500 mm Number of cylinders 3 pcs Tool installation space   Distance table stö&aerospace;el OT 2,300 mm Distance table-stö&aerospace;el UT 600 mm Table clamping area (width x depth) 5,000 X 2,500 mm T-slot pitch 300 mm Öffnung zwischen den Führungen 5,040 mm Press static   Allowable deflection at 2/3 surface load, related to the table length (l. - r.)   Table top max. 0, 125 mm/m Stö&Area;el max. 0, 125 mm/m Length of drawing rod, approx. 2,500 mm Max. external moment   Left - Right 1.870 kNm Front - Rear 935 kNm Hydraulic 8-point table cushion   Displacement force 900-6,000 kN Number of separately adjustable pressure points 8 pcs Ejector force (net, fixed) 500 kN Table cushion stroke total 380 mm Table cushion useful stroke 350 mm Table cushion area (width x depth) (referred to centre of first rows of push pins) 4,200 X 2,100 mm Ejector speed 100 mm/s Pen matrix 29 X 15  pcs Printing pin pitch 150 mm Pin diameter 45 mm Hydraulic cushion in the rod   Displacement force 450- 3,000  kN Ejector force (not adjustable) 200 kN Cushion stroke max 200 mm Cushion area (width x depth){referring to middle äußfirst pressure pin rows) 4,200 X 2,100 mm Return speed 100 mm/s Pen matrix 29 x 15 Printing pin pitch 150 mm Pin diameter 45 mm Mechanical stroke limitation   Number of spindles 2 pcs Position of the spindles Page spindles  Stroke limiting force max 7,500 kN Spindle adjustment range 850 mm Effective range over table 600 - 1,450 mm Tool clamp on stand   Number 12 pcs Type Insertion clamp Tensioning force Each 100  kN Stroke 12 mm Drive table   Number of driving tables 1 pc Direction of extension to the front Travel distance from the press 3,500 mm Travel speed (rapid/creep speed) 15/2 m/min Max. Tool weight 60 t Max. Weight upper tool 30 t Connections for tools   Position Pages • Compressed air controlled 2x½" Piece • Compressed air uncontrolled 2x½" Stück • hydraulics controlled 4 x pcs Hydraulic pressure ND 3 x 50 bar Hydraulic pressure HD 1 x 300 bar Ölvolume 30 l/min Nominal size G½"  • WZ- control 1 x H AN 24 pcs • Sockets - 230 V / 16A 2 pcs • Sockets - 400 V / 16A 1 pc  • Sockets - 400 V / 32A 1 pcück  Speeds   Rapid lowering speed 400  mm/s Rail return speed Stößel 400  mm/s Working speed V1 max. up to max. ~3,900kN 265  mm/s  V2 max. up to max. -6600kN 132  mm/s  V3 max up to max -9.3 00kN 88  mm/s  V at nominal force (25.000 kN) 36  mm/s  Main drive   Motor power for main pumps 3 x200  kW Total installed power approx. approx. 720  kW Pump flow max. 3 X 1,400  l/min Maximum hydraulic system pressure 310 bar Press main dimensions   Press height over corridor  < 9,500  mm Press width at corridor level, approx. 7 .000  mm Press width at headboard level, approx. 8,800  mm  Press depth at corridor level, approx. 3,500  mm Press depth at header level, approx. 5,200  mm High fixture area above corridor 500  mm Delivery time immediately Price on request

Spotting try out press   Manufacturer Ona Model 2400 spotting force 2400t Year of manufacture 2006 Comment   Technical Data   Connection points 4 Drive system Hydraulic Maximum tonnage 2,400 tonnes Support surface & carriage 4,800 mm x 2,400 mm Top of carriage above ground level 800 mm Carriage stroke 1,700 mm Maximum closing height N/A Maximum daylight 2600 mm Minimum closing height 900 mm Front clearance between oil drip pans 4,650 mm Lateral clearance between uprights 1,600 (width) x 2,600 mm (height from floor) Maximum free-standing height N/A Main motor Siemens, AC Number of driven movable bolsters 1 (front) min 4.5 m travel Clamp jaws Four (4) x 12 ton Hydraulic type Lower die clamps Manually bolted Size of "T" slots 1 1/16" T-slot (front-rear) Spacing of "T" slots in die holder 6". Max. weight of upper die 25 tons Max. weight of the whole die 50 tons Upper clamps Eight x 10T Hyd Manually placed Dampers Standard Hydraulic Suspension / number of cylinders 2 pads with two cylinders per pad Maximum damping tonnage 2 x 250T = 500T Area of damping pad 2 pads of 2,000 mm x 1,900 mm Damping stroke 400 mm Distance of damping bolts 6" grid spacing Damping pin diameter 1 9/16" (2 x 7/16 C'Bore) Cushion Pin Supply Included Slide Lock Four (4) x Hyd Spring Locking Elements Safety Stamp Blocks Nil Tool service connections Auto-pneumatic & electric multi couplings Cooling water requirement TBA Air consumption requirement TBA Power requirement 415v @50 hz Height restriction (crane spacing) 10.95m Electrical & Control   Press control and diagnostics 10" touch screen, HMI with 100 part memory library Tonnage monitoring 4-point measurement Control circuits (all) 24 Volt DC Press control and diagnostics Siemens Protective devices and safety stops category 4 Delivery time immediately Price on request

Spotting try out press   Manufacturer Reis Model TUS 60-40 spotting force 400 kN / 40t Year of manufacture 2001 Comment   Technical Data   Passage between columns 620 x 620 mm Table surface 670 x 570 mm max. mould weight  kg max. swing weight  kg Ejector force table  kN Ejector stroke table  mm Ejector carft ram 48 kN Ejector stroke ram  mm Connected load 10 kVA Drive power 7,5 kW Machine weight 10t Delivery time immediately Price on request

Spotting try out press   Manufacturer Daxian Model DXS - 4025 - 400 spotting force 4000 kN / 400t Year of manufacture 2016 Comment   Technical Data   Table surface 4000 x 2500 mm Lifting force 1000 kN max. open strocke 2750 mm Ejector stroke 6500 mm Drive power 55 kW Delivery time immediately Price on request

Spotting try out press   Manufacturer Reis Model TUS 100 spotting force 1000 kN / 100t Year of manufacture 1996 Comment   Technical Data   Table surface 1300 x 1000 mm max. mould weight 8000 kg max. swing weight 4000 kg Ejector force table 35 kN Ejector stroke table 115 mm Ejector carft ram 48 kN Ejector stroke ram 150 mm Connected load 10 kVA Drive power 7,5 kW Machine weight 10t Delivery time immediately Price on request

Spotting try out press   Manufacturer Schnupp Model Schnupp 500 t spotting force 5000 kN / 500 t Year of manufacture 2011 Comment   Technical Data   Table surface 5000 x 2500 mm dimension of pit lifting frame 10000 x 8000 x 5000 mm max ram stroke 2000 mm max. tool dimension 5000 x 2500 mm min. tool dimension 1200 x 700 mm max. tool height 1500 mm min. tool height 500 mm weight of top tool max. 30 t total weight of tool max. 50 t Drive power 300 kW Machine weight 200 t Delivery time immediately Price on request

Spotting try out press   Manufacturer Schuler Model WWV-100-30/4700-2450 spotting force 1000 kN / 100 t Year of manufacture 2001 Comment   Technical Data   Table surface 4700 x 2450 mm Installation height 2960 mm max. tool dimension 4500 x 2400 mm min. tool dimension 1900 x 1900 mm max. tool height 1525 mm min. tool height 650 mm weight of top tool max. 30 t total weight of tool max. 60 t Drive power 140 kW Machine weight 110 t Delivery time immediately Price on request